Progressive Automotive, mustang II IFS 2 front suspensions

Progressive Automotive, independant front suspensions, mustang 2 suspension, mustang suspension, mustang II suspension, suspension kit, Street Rods, Street Rod, Classic Trucks, Classic Truck, Corvettes, Corvette, Chevy, Chevrolet, Ford, Plymouth, Mercury, Lincoln, Dodge, Chrysler, GMC, 1955 Chevy, 1956 Chevy, 1957 Chevy, Coupe, Sedan, truck, panel, nomad, roadster, cabriolet,

"Street Ryde" Mustang II Based Front Suspension

Back to the Progressive Automotive Main Page

Call (740) 862-4696 for your needs!

"Street Ryde" Suspension Kits

Complete "Street Ryde" Suspension Package and options shown

Each Street Ryde kit is specifically designed for each vehicle and pre-cut to fit your frame, not some jig saw puzzle kit!

Our suspension bracketry is welded inside and out, and constructed from 3/16" material, even the upper control arm mounts.

We give you twice the amount of alignment capability as the original Ford Mustang II design.

Axle centerline is clearly marked on the crossmember and upper mounts.

Our lower crossmember and upper arm mounts are ground to a smooth finish. ready for primer and paint.

Our lower control arm tube is one piece and crossmember closed for additional strength & appearance.

Don't think that a Mustang II based suspension can take the being a daily driver? Especially on a Truck?

Then you need to look at this link: www.chuckthetruck.com

Illinois Daily Drive for 5 year and 45,000 miles with out Street Ryde front suspension and Pro-Slip Leaf Spring rear.

Road Race Tested! Check Here

Complete "Street Ryde" Suspension

Complete hub to hub suspensions include: The appropriate bracketry kit for your vehicle, Steel tubular upper control arms, steel tubular "Strut-Less" lower control arms, spindles, outer tie rod ends, gas shocks, springs, urethane coil spring insulators, "Big Brakes" with either Ford or Chevrolet bolt pattern rotors, rotor bearings, rotor seals, spindle nuts, spindle nut cages cotter pins, spindle washers, rotor dust caps, "Big Brake" calipers with brake pads, anti-rattle clips, "Big Brake" caliper mounts and all mounting hardware!

"Street Ryde" Suspension parts shown, rack & pinion included, but not shown in photo

Additional Options for Complete suspensions

Front boxing kit, ........................IFS-BP...add $89.00

2" Drop spindles, in place of stock style spindles, ........................PA-DRP....No Charge

Power rack & pinion in place of manual, ........................PA-POW.... No Charge

Black powder coated control arms, add........................$90.00

Black powder coated spindles, add........................$40.00

Polished stainless arms, in place of steel arms, add........................$830.00

Air Ride Technologies "Shockwaves" in place of springs/shocks........................PA-IFS-SW....add $816.00

Front sway bar, ........................PA-FSB-TA....add $179.00

Front sway bar for 1942-56 Ford trucks and 1955 (2nd Ser.)-59 Chevy trucks, ........................PA-FSB-TTA....add $179.00

1953-62 Corvette Front sway bar, ........................PA-FSB-VTA....add $199.00

Torsional front sway bar for Air ride, add........................... $455.00

*11" Turbo slot rotors (zinc washed), 2-piston (38 mm) Sport Twin aluminum calipers , clears 15" wheels

*Kit with Powdercoated calipers, $547.00

*Kit with Polished calipers, $597.00

*Optional Cross-Drilled rotors, add $140.00

*11" Turbo slot rotors (zinc washed), 4-piston (45mm) aluminum Elite calipers, clears 15" wheels.

*Kit with Powdercoated calipers, $847.00

*Kit with Polished calipers, $896.00

*Optional Cross-Drilled rotors, add $140.00

*13" Turbo slot rotors (zinc washed), 3-piston (38mm) aluminum Tri-Power calipers, clears 15" wheels. ,

*Kit with Powdercoated calipers, $1,211.00

*Kit with Polished calipers, $1,261.00

*Optional Cross-Drilled rotors, add $140.00

*13" Turbo slot rotors (zinc washed), 4-piston (43mm) Extreme aluminum calipers, clears 18" wheels,

*Kit with Powdercoated calipers, $1,361.00

*Kit with Polished calipers, $1,411.00

*Optional Cross-Drilled rotors, add $140.00

*Note, We do recommend that your frame be boxed. Click here for our boxing plates. A must when installing X-members, rear suspension and motor mounts.

Ford Cars & Trucks:

1928-31 Model A

"Street Ryde" kit includes (2) manual rack extenders, upper arm mounts, tubular upper control arms, lower crossmember, tubes installed for our lower control arms, bolts and washers for rack & pinion mounting and complete instructions. "Street Ryde" Kit IFS-A......$840.00

Ride height with drop spindles is even with the bottom of the frame.

Complete "Street Ryde" Suspension Package....IFS-A-C.... $1,944.00

IFS-A shown, tubular upper control arms included but not shown in photos

1932 Ford car/33 (1st Ser.)-33 truck

"Street Ryde" kit includes upper arm mounts, lower crossmember, tubes installed for our lower control arms, bolts and washers for rack & pinion mounting and complete instructions. "Street Ryde" Kit IFS-32F......$499.00

Ride height with drop spindles is 1" above the bottom of the frame.

Complete "Street Ryde" Suspension Package....IFS-32F-C.... $1,902.00

1933-34 Ford car

Ride height with stock spindles is 1" above the bottom of the frame.

Complete "Street Ryde" Suspension Package....IFS-34F-C.... $1,877.00

1933 (2nd Ser.)-34 Ford trucktruck

Ride height with drop spindles is even with the bottom of the frame.

Complete "Street Ryde" Suspension Package....IFS-33T-C.... $1,902.00

1935-40 Ford car /1935-41 truck

Ride height with stock spindles is 1" above the bottom of the frame.

Complete "Street Ryde" Suspension Package....IFS-35F-C.... $1,877.00

IFS-35F-C "Street Ryde" Suspension with options shown

1941-48 Ford car

Ride height with stock spindles is 1" above the bottom of the frame.

Complete "Street Ryde" Suspension Package....IFS-41F-C.... $1,877.00

IFS-41F-C "Street Ryde" Suspension with Shockwave options shown

1949-51 Ford car

"Street Ryde" kit includes rails from the firewall, boxing plates, upper arm mounts, lower crossmember and tubes installed for our lower control arms. Uses original core support. "Street Ryde" Kit IFS-49F......$1,499.00

Ride height with stock spindles is 1" above the bottom of the frame.

Complete "Street Ryde" Suspension Package....IFS-49F-C.... $2,913.00

IFS-49F-C "Street Ryde" Suspension Package shown

1955-57 Thunderbird car

"Street Ryde" kit includes rail section, boxing plates, upper arm mounts, lower crossmember and tubes installed for our lower control arms. "Street Ryde" Kit IFS-57TB......$1,069.00

Ride height with stock spindles is even with the bottom of the frame.

Complete "Street Ryde" Suspension Package....IFS-57TB-C.... $2,472.00

IFS-57TB with Complete "Street Ryde" Suspension Package and options shown

1962-65 Ford Falcon/Ranchero

"Street Ryde" kit power rack extender, upper arm mounts, lower crossmember, tubes installed for our lower control arms, bolts and washers for rack & pinion mounting and complete instructions. "Street Ryde" Kit IFS-63F......$499.00

Ride height with stock spindles is stock.

Complete "Street Ryde" Suspension Package....IFS-63F-C.... $1,913.00

1942-47 truck

"Street Ryde" kit includes power rack extender, upper arm mounts, lower crossmember, tubes installed for our lower control arms, bolts and washers for rack & pinion mounting and complete instructions. "Street Ryde" Kit IFS-42T......$499.00

Ride height with stock spindles is 1" above the bottom of the frame.

Complete "Street Ryde" Suspension Package....IFS-42T-C.... $1,902.00

IFS-42T "Street Ryde" bracketry kit shown

1948-52 truck

"Street Ryde" kit includes power rack extender,upper arm mounts, lower crossmember, tubes installed for our lower control arms, bolts and washers for rack & pinion mounting and complete instructions. "Street Ryde" Kit IFS-48T......$499.00

Ride height with stock spindles is 1" above the bottom of the frame.

Complete "Street Ryde" Suspension Package....IFS-48T-C.... $1,902.00

1953-59 truck

"Street Ryde" kit includes power rack extenders,upper arm mounts, lower crossmember, tubes installed for our lower control arms, bolts and washers for rack & pinion mounting and complete instructions. "Street Ryde" Kit IFS-53T......$544.00

Ride height with stock spindles is 1" above the bottom of the frame.

Complete "Street Ryde" Suspension Package....IFS-53T-C.... $1,958.00

IFS-53T-C "Street Ryde" Suspension and options shown

Chevrolet:

1928-32Chevy car / 1928-33 Truck

"Street Ryde" kit includes manual rack extender, upper arm mounts, lower crossmember, tubes installed for our lower control arms, bolts and washers for rack & pinion mounting and complete instructions. "Street Ryde" Kit IFS-32C......$529.00

Ride height with drop spindles is 2" above the bottom of the frame.

IFS-32C "Street Ryde" bracketry kit shown

Complete "Street Ryde" Suspension Package....IFS-32C-C.... $1,932.00

1933 Chevy

Optional core supports add, ...IFS-33C-CS....$89.00

Ride height with stock spindles is 1" above the bottom of the frame.

Complete "Street Ryde" Suspension Package, includeds core supports....IFS-33C-C.... $1,877.00

1934-36 Chevy standard

"Street Ryde" kit includes upper arm mounts, lower crossmember, tubes installed for our lower control arms, bolts and washers for rack & pinion. "Street Ryde" Kit IFS-34C......$474.00

Optional core supports add..IFS-34C-CS.... $89.00

Ride height with stock spindles is 1" above the bottom of the frame.

Complete "Street Ryde" Suspension Package, includeds core supports....IFS-34C-C.... $1,877.00

IFS-34C-C "Street Ryde" Suspension and options shown, Core support not shown in photo

1934-35 Chevy Master

Optional core supports add...IFS-34M-CS.... $89.00

Ride height with stock spindles is 1" above the bottom of the frame.

Complete "Street Ryde" Suspension Package, includeds core supports....IFS-34M-C.... $1,877.00

1936 Chevy master-48 Chevy

"Street Ryde" kit includes 4 brace plates, upper arm mounts, lower crossmember, tubes installed for our lower control arms, bolts and washers for rack & pinion mounting and complete instructions. "Street Ryde" Kit IFS-36M......$490.00

Ride height with stock spindles is 1" above the bottom of the frame.

Complete "Street Ryde" Suspension Package....IFS-36M-C.... $1,893.00

IFS-36M "Street Ryde" bracketry kit shown

IFS-36M-C "Street Ryde" Suspension with options shown

1949-54 Chevy cars

"Street Ryde" kit includes C-notches and brace plates, upper arm mounts, lower crossmember, tubes installed for our lower control arms, bolts and washers for rack & pinion mounting and complete instructions. "Street Ryde" Kit IFS-49C......$524.00

Ride height with stock spindles is 1" above the bottom of the frame.

Complete "Street Ryde" Suspension Package....IFS-49C-C.... $1,927.00

IFS-49C "Street Ryde" bracketry kit shown

1955-57 Chevy cars

"Street Ryde" kit includes rails from the firewall, core support, boxing plates, upper arm mounts, and tubes installed for our lower control arms, lower crossmember.. "Street Ryde" Kit IFS-55C......$2,199.00

Ride height with stock spindles is 1" above the bottom of the frame.

Complete "Street Ryde" Suspension Package....IFS-55C-C.... $3,613.00

1953-62 Corvette

Optional core support/bumperette mounts add ....IFS-62C-CS.........$110.00

Ride height with stock spindles is same as stock.

Complete "Street Ryde" Suspension Package, includes core support....IFS-62C-C.... $1,892.00

Corvette with IFS-62C-C "Street Ryde" shown with drop spindles

IFS-62C-C "Street Ryde" Suspension Package and options shown

1934-36 Chevy trucks

Ride height with stock spindles is 1" above the bottom of the frame.

Complete "Street Ryde" Suspension Package....IFS-34T-C.... $1,877.00

IFS-34T "Street Ryde" bracketry kit shown

1937-40 truck

"Street Ryde" kit includes C-notches, upper arm mounts, lower crossmember, tubes installed for our lower control arms, bolts and washers for rack & pinion mounting and complete instructions. "Street Ryde" Kit IFS-37T......$499.00

Ride height with stock spindles is 1" above the bottom of the frame.

Complete "Street Ryde" Suspension Package....IFS-37T-C.... $1,902.00

IFS-37T "Street Ryde" bracketry kit shown

1941-46 truck

Ride height with stock spindles is 1" above the bottom of the frame.

Complete "Street Ryde" Suspension Package....IFS-41T-C.... $1,902.00

IFS-41T "Street Ryde" bracketry kit shown

IFS-41T-C "Street Ryde" Suspension Package and Shockwaves shown

1947-55 (1st series) trucks

Ride height with stock spindles is 1" above the bottom of the frame.

Complete "Street Ryde" Suspension Package....IFS-47T-C.... $1,902.00

IFS-47T "Street Ryde" bracketry kit shown

IFS-47T with Complete "Street Ryde" Suspension and options shown

1955 (2nd series)-59 trucks

"Street Ryde" kit includes power rack extenders, upper arm mounts, lower crossmember, tubes installed for our lower control arms, bolts and washers for rack & pinion mounting and complete instructions. "Street Ryde" Kit IFS-55T......$544.00

Ride height with stock spindles is 1" above the bottom of the frame.

Complete "Street Ryde" Suspension Package....IFS-55T-C.... $1,958.00

Plymouths:

1933 Plymouths

"Street Ryde" kit includes upper arm mounts, lower crossmember, tubes installed for our lower control arms, bolts and washers for rack & pinion mounting and complete instructions. "Street Ryde" Kit IFS-33P......$44.00 *Must fill out our IFS Tech sheet

Ride height with stock spindles is 1" above the bottom of the frame.

Complete "Street Ryde" Suspension Package....IFS-33P-C.... $1,888.00

IFS-33P-C "Street Ryde" Suspension Package shown

1934 Plymouths (for Non-stock independents)

"Street Ryde" kit includes upper arm mounts, lower crossmember, tubes installed for our lower control arms, bolts and washers for rack & pinion mounting and complete instructions. "Street Ryde" Kit IFS-34P......$474.00 *Must fill out our IFS Tech sheet

Ride height with stock spindles is 1" above the bottom of the frame.

Complete "Street Ryde" Suspension Package....IFS-34P-C.... $1,888.00

1934 Plymouths (for stock independents)

"Street Ryde" kit includes rails from the firewall, core support, boxing plates, upper arm mounts, lower crossmember, tubes installed for our lower control arms, bolts and washers for rack & pinion mounting and complete instructions. "Street Ryde" Kit IFS-P34......$2,225.00

Ride height with stock spindles is 1 1/2" above the bottom of the frame.

Complete "Street Ryde" Suspension Package....IFS-P34-C.... $3,639.00

1939-41 Plymouths

"Street Ryde" kit includes rails from the firewall, core support, and boxing plates, upper arm mounts, lower crossmember, tubes installed for our lower control arms, bolts and washers for rack & pinion mounting and complete instructions. "Street Ryde" Kit IFS-P39......$2,225.00

Ride height with stock spindles is 1 1/2" above the bottom of the frame.

Complete "Street Ryde" Suspension Package....IFS-P39-C.... $3,639.00

IFS-P39 kit shown

1942-48 Plymouths

"Street Ryde" kit includes rails from the firewall, core support and boxing plates, upper arm mounts, lower crossmember, tubes installed for our lower control arms, bolts and washers for rack & pinion mounting and complete instructions. "Street Ryde" Kit IFS-P42......$2,225.00

Ride height with stock spindles is 1" above the bottom of the frame.

Complete "Street Ryde" Suspension Package....IFS-P42-C.... $3,639.00

Willys:

1937-41 Willys Car & Truck:

Ride height with stock spindles is 1" above the bottom of the frame.

Complete "Street Ryde" Suspension Package....IFS-37W-C.... $1,877.00

1948-51 Willys Jeepster:

Ride height with stock spindles is 1" above the bottom of the frame.

Complete "Street Ryde" Suspension Package....IFS-48WJ-C.... $1,927.00

IFS-48WJ "Street Ryde" bracketry kit shown

Custom built kits are available for vehicle's that are not listed. Just fill out the IFS Tech sheet (for vehicles that have bare frame rails) or our IFS & Rails Tech sheet (for vehicles that have coil-spring pockets stamped into the frame rails) and send it to the address on the Home page!

Back to the Progressive Automotive Main Page

Call (740) 862-4696 for your needs!